Stanley Automatic Sliding Door Adjustments - 4 Secret Tips!



Stanley automatic sliding doors are by far the most popular door system in America. Stanley doors are everywhere you go. From hospitals to libraries, Stanley automatic doors can be found. You may walk through Stanley automatic sliding doors and take them for granted. But when analyzed there is actually alot of moving parts that make the door operate properly. In this article we go over 4 secret tips on Stanley automatic sliding door adjustments.

Tip #1: How To Align Your Door Panels

Have you ever noticed that your automatic doors were not aligned. When the doors shut, you see that there is an uneven space when the two sliding panels meet together at the center of the doorway. Well this is actually extremely easy to fix. First turn the power off so that the doors are not powered. Next, you need to open the header. There is a screw at each end of the header. Unscrew both fasteners. The header is hinged and will pull out and lift up. Sometimes the header cover may be a tight fit. Once the header is open you will notice that there are 4 big nuts at the top of each active/moving door panel. 2 of the nuts are for the anti-riser wheels. The anti-riser wheel is designed to be adjusted just under the metal track extrusion, such that if the door panel gets bumped or lifted in the upward direction, the anti-riser will hit the metal track extrusion, and the door will not get derailed. The other 2 nuts are the urethane track roller wheels. The urethane track roller wheel is comprised of an eccentric allen key stud with a threaded nut. When you insert an allen key wrench into the stud of the roller and rotate it either clockwise or counter clockwise, the door height will raise or lower. Do this to both moving door panels until the door alignment is suitable. Keep in mind the nut on the outside of the roller stud must be loosened in order to rotate the allen key. Once the desired door alignment is set tightened the nut on the roller stud. Then set the antiriser wheels to the appropriate height and tightened the antiriser nuts. It is important that when you are done, make sure that the anti-riser wheels are not rolling on the metal extrusion. If they do, this will wear out the anti-riser wheels.

Stanley 312462 Automatic Door Antiriser Wheel Assembly

Stanley 972312729 Automatic Door Track Roller Assembly


Tip #2: How To Replace The Belt

Is your Stanley automatic sliding door noisy? Do you hear a high pitched squeaky sound at the top of the door somewhere. Is louder at different temperatures? Or is it pretty much the same loud squeaky sound whenever the door opens or closes. Chances are your Stanley automatic sliding door belt is worn out. But don't worry! It is very easy to replace. First thing to do is measure the width of your entire Stanley door package (this means the entire width of all door panels). Once you find this then multiply by 2 and this is the approximate length (feet) of timing belt you need to purchase. Begin by shutting the power off to the door and opening the header. You will see that the belt wraps around the gearbox pulley on one side and an idler pulley on the other side. The belt connects to the door panels by 2 belt clips if you have a 4 panel door (bi-part), or 1 belt clip if you have a 2 panel door (single slide). Remove the belt clips and the belt. Cut the new belt to the exact length and install new belt. Important, especially on a 4 panel door (bi-part) to install the belt clips in the correct position. If you accidentally install the lower belt clip in the upper position, or vice versa the door will open and close in the opposite direction.

Stanley Automatic Sliding Door Timing Belt For Bi-Parts and Single Slides

Tip #3: How To Replace The Bottom Guide

Bottom guides are located at the bottom of each moving door panel. They guide the moving door panel as it moves. Without a bottom guide, the door panel would not be secure when sliding open or closed. There are 2 types of Stanley bottom guides, depending on which Stanley door configuration you have. If you have a Stanley door system where all door panels (moving and stationary door panels) can swing out, then you have a full breakout bottom guide. If you have a Stanley door configuration where only the moving door panels can swing out and the stationary panels cannot, then you have a fixed sidelite bottom guide. To replace any Stanley bottom guide, first start by turning the power to the door off. Then loosen the antirisers, so that you can lift the door. Carefully slide the door open, and then lift it off of the track. Set the door on it's side. From there you can access the bottom guide. Full breakout bottom guides are held in by 4 phillips fasteners. While the fixed sidelite bottom guides are held in by 2 phillips fasteners. Bottom guides wear out. A defective bottom guide can cause the Stanley automatic doors to not close, but reopen. This is very common when the bottom guide gets jammed or sticks, and the automatic door controller thinks there is an obstruction, so it reopens the door. Defective bottom guides can also make a lot of noise. If you hear noise at the bottom of your door, your bottom guides will need replacement.

Stanley 515191 Right Hand Fixed Sidelite Bottom Guide

Stanley 515192 Left Hand Fixed Sidelite Bottom Guide

Stanley 515265 Full Breakout Bottom Guide Assembly


Tip #4 How To Adjust Your Automatic Door Sensor

For information regarding the available adjustments of the Stanley SU100 automatic door sensor please read our article, "Stanley Automatic Door Sensor Adjustments - What You Need To Know!"

Stanley SU100 Automatic Door Sensor


With these 4 tips you will be able to adjust your Stanley Automatic Sliding Door. Please keep in mind to always refer to the manufacturer's instructions and information, as it is constantly updated and always make sure these adjustments are made by certified automatic door technicians. Of course if you have any questions feel free to contact us at custsvc@autodoorandhardware.com . And if you need any Stanley automatic door replacement parts you can purchase them on our website below.

Buy Stanley Automatic Door Parts Here


Comments

  1. I am attracted by the presentation of this article. This information about top rollers is really good. I really appreciate your work. It is a gainful article for us. Keep posting. Thank you. table top rollers

    ReplyDelete
  2. You've provided some very useful information. I'm glad I came into this article because it provides a lot of important information. Thank you for sharing this storey with us. Roller Doors

    ReplyDelete
  3. Got some wonderful knowledge from this post. I got some great information from the article you have published in this post. Keep Posting . Industrial Door Supplier

    ReplyDelete
  4. The doors allow for great views of the garden and can really compliment the overall house design. Not only do patio doors provide extreme beauty, they are also a very energy efficient product. They allow for natural light to be added to your home causing less need for air conditioning or heating units to be used.Conservatory installers

    ReplyDelete
  5. This article provided me with a wealth of information. The article is incredibly helpful and offers some of the most useful information Aftermarket john deere dozer parts. Thank you for sharing it with us.

    ReplyDelete
  6. You've written an excellent post, and you've shared it with us. Your article provided me with some unique and useful knowledge farmhouse sliding door. I appreciate you sharing this text with us.

    ReplyDelete
  7. This article provided me with a wealth of information about Sliding Barn Doors in Orange. The article is incredibly helpful and offers some of the most useful information. Thank you for sharing it with us.

    ReplyDelete
  8. Many timber framing companies use some form of mortise and tenon joinery for their building system, but how do you want the timbers to be cut? Know them from https://www.timberstruc.co.uk

    ReplyDelete
  9. I am very thankful to you that you have shared this information with us. Read more info about Windows Installation Columbus. I got some different kind of knowledge from your web page, and it is really helpful for everyone. Thanks for share it.

    ReplyDelete
  10. I admire this article for the well-researched content and excellent wording. Portland Exterior Painting Company. I got so involved in this material that I couldn’t stop reading. I am impressed with your work and skill. Thank you so much.

    ReplyDelete

Post a Comment